51單片機蜂鳴器播放音樂代碼(生日快樂 兩只蝴蝶祝你平安)

ID:80436 · 發表于 2015-5-20 18:18

本帖最后由 liuqq 于 2015-5-20 18:20 編輯

/*生日快樂歌曲*/
/*******************************************/

#include <reg51.h>
#define uint unsigned int
#define uchar unsigned char
sbit beep = P1^5;
uchar code SONG_TONE[]={212,212,190,212,159,169,212,212,190,212,142,159,
212,212,106,126,159,169,190,119,119,126,159,142,159,0};
uchar code SONG_LONG[]={9,3,12,12,12,24,9,3,12,12,12,24,
9,3,12,12,12,12,12,9,3,12,12,12,24,0};
//延時
void DelayMS(uint x)
{
uchar t;
while(x--) for(t=0;t<120;t++);
}
void PlayMusic()
{
uint i=0,j,k;
while(SONG_LONG[i]!=0||SONG_TONE[i]!=0)
{ //播放各個音符，SONG_LONG 為拍子長度
for(j=0;j<SONG_LONG[i]*20;j++)
{
beep=~beep;
//SONG_TONE 延時表決定了每個音符的頻率
for(k=0;k<SONG_TONE[i]/3;k++);
}
DelayMS(10);
i++;
}
}
void main()
{
beep=0;
while(1)
{
PlayMusic(); //播放生日快樂
DelayMS(500); //播放完后暫停一段時間
}
}

復制代碼

/*兩只蝴蝶歌曲*/
/*******************************************/

#include <reg51.h> // 這是單片機音樂代碼生成器生成的代碼
#define uchar unsigned char
sbit beepIO=P1^5; // 輸出為 P1.5 可以修改成其它 IO 口
uchar m,n;
uchar code T[49][2]={{0,0},
{0xF8,0x8B},{0xF8,0xF2},{0xF9,0x5B},{0xF9,0xB7},{0xFA,0x14},{0xFA,0x66},{0xFA,0xB9},{0xFB,0x03},{0xFB,0x4A},{0xFB,0x8F},{0xFB,0xCF},{0xFC,0x0B},
{0xFC,0x43},{0xFC,0x78},{0xFC,0xAB},{0xFC,0xDB},{0xFD,0x08},{0xFD,0x33},{0xFD,0x5B},{0xFD,0x81},{0xFD,0xA5},{0xFD,0xC7},{0xFD,0xE7},{0xFE,0x05},
{0xFE,0x21},{0xFE,0x3C},{0xFE,0x55},{0xFE,0x6D},{0xFE,0x84},{0xFE,0x99},{0xFE,0xAD},{0xFE,0xC0},{0xFE,0x02},{0xFE,0xE3},{0xFE,0xF3},{0xFF,0x02},
{0xFF,0x10},{0xFF,0x1D},{0xFF,0x2A},{0xFF,0x36},{0xFF,0x42},{0xFF,0x4C},{0xFF,0x56},{0xFF,0x60},{0xFF,0x69},{0xFF,0x71},{0xFF,0x79},{0xFF,0x81}
};
uchar code music[][2]={{0,4},
{23,4},{21,4},{23,16},{23,4},{21,4},{23,4},{21,4},{19,16},{16,4},{19,4},{21,8},{21,4},{23,4},{21,4},{19,4},{16,4},{19,4},{14,24},
{23,4},{21,4},{23,16},{23,4},{21,4},{23,4},{21,4},{19,24},{16,4},{19,4},{21,8},{21,4},{23,4},{21,4},{19,4},{16,4},{19,4},{21,24},
{23,4},{21,4},{23,16},{23,4},{21,4},{23,4},{21,4},{19,16},{16,4},{19,4},{21,8},{21,4},{23,4},{21,4},{19,4},{16,4},{19,4},{14,24},
{23,4},{26,4},{26,16},{26,4},{28,4},{26,4},{23,24},{21,4},{23,4},{21,8},{21,4},{23,4},{21,4},{19,4},{16,4},{16,2},{19,2},{19,24},{0,20},
{26,4},{26,4},{28,4},{31,4},{30,4},{30,4},{28,4},{23,4},{21,4},{21,4},{23,16},{0,4},{23,4},{23,4},{26,4},{28,8},{28,12},{16,4},{23,4},{21,4},
{21,24},{23,4},{26,4},{26,4},{23,4},{26,8},{0,4},{31,8},{30,4},{28,4},{30,4},{23,8},{0,4},{28,4},{28,4},{30,4},{28,4},{26,4},{23,4},{21,8},{23,4},{21,4},{23,4},{26,16},
{0xFF,0xFF}};
void delay(uchar p)
{
uchar i,j;
for(;p>0;p--)
for(i=181;i>0;i--)
for(j=181;j>0;j--);
}
void pause()
{
uchar i,j;
for(i=150;i>0;i--)
for(j=150;j>0;j--);
}
void T0_int() interrupt 1
{
beepIO=!beepIO;
TH0=T[m][0]; TL0=T[m][1];
}
void main()
{
uchar i=0;
TMOD=0x01; EA=1; ET0=1;
while(1)
{
m=music[i][0];n=music[i][1];
if(m==0x00)
{TR0=0;delay(n);i++;}
else if(m==0xFF)
{TR0=0;delay(30);i=0;}
else if(m==music[i+1][0])
{TR0=1;delay(n);TR0=0;pause();i++;}
else
{TR0=1;delay(n);i++;}
}
}

復制代碼

祝你平安：

#include "reg52.h"
unsigned char Count;
sbit _Speak =P1^5 ;
unsigned char code SONG[] ={ //祝你平安
0x26,0x20,0x20,0x20,0x20,0x20,0x26,0x10,0x20,0x10,0x20,0x80,0x26,0x20,0x30,0x20,
0x30,0x20,0x39,0x10,0x30,0x10,0x30,0x80,0x26,0x20,0x20,0x20,0x20,0x20,0x1c,0x20,
0x20,0x80,0x2b,0x20,0x26,0x20,0x20,0x20,0x2b,0x10,0x26,0x10,0x2b,0x80,0x26,0x20,
0x30,0x20,0x30,0x20,0x39,0x10,0x26,0x10,0x26,0x60,0x40,0x10,0x39,0x10,0x26,0x20,
0x30,0x20,0x30,0x20,0x39,0x10,0x26,0x10,0x26,0x80,0x26,0x20,0x2b,0x10,0x2b,0x10,
0x2b,0x20,0x30,0x10,0x39,0x10,0x26,0x10,0x2b,0x10,0x2b,0x20,0x2b,0x40,0x40,0x20,
0x20,0x10,0x20,0x10,0x2b,0x10,0x26,0x30,0x30,0x80,0x18,0x20,0x18,0x20,0x26,0x20,
0x20,0x20,0x20,0x40,0x26,0x20,0x2b,0x20,0x30,0x20,0x30,0x20,0x1c,0x20,0x20,0x20,
0x20,0x80,0x1c,0x20,0x1c,0x20,0x1c,0x20,0x30,0x20,0x30,0x60,0x39,0x10,0x30,0x10,
0x20,0x20,0x2b,0x10,0x26,0x10,0x2b,0x10,0x26,0x10,0x26,0x10,0x2b,0x10,0x2b,0x80,
0x18,0x20,0x18,0x20,0x26,0x20,0x20,0x20,0x20,0x60,0x26,0x10,0x2b,0x20,0x30,0x20,
0x30,0x20,0x1c,0x20,0x20,0x20,0x20,0x80,0x26,0x20,0x30,0x10,0x30,0x10,0x30,0x20,
0x39,0x20,0x26,0x10,0x2b,0x10,0x2b,0x20,0x2b,0x40,0x40,0x10,0x40,0x10,0x20,0x10,
0x20,0x10,0x2b,0x10,0x26,0x30,0x30,0x80,0x00};
void Time0_Init()
{
TMOD = 0x01;
IE = 0x82;
TH0 = 0xD8;
TL0 = 0xEF; //12MZ晶振，10ms
}
void Time0_Int() interrupt 1
{
TH0 = 0xD8;
TL0 = 0xEF;
Count++; //長度加1
}
/*-------------------------------------------------
功能:1MS延時子程序
-------------------------------------------------*/
void Delay_xMs(unsigned int x)
{
unsigned int i,j;
for( i =0;i < x;i++ )
{
for( j =0;j<3;j++ );
}
}
void Play_Song(unsigned char i)
{
unsigned char Temp1,Temp2;
unsigned int Addr;
Count = 0; //中斷計數器清0
Addr = i * 217;
while(1)
{
Temp1 = SONG[Addr++];
if ( Temp1 == 0xFF ) //休止符
{
TR0 = 0;
Delay_xMs(100);
}
else if ( Temp1 == 0x00 ) //歌曲結束符
{
return;
}
else
{
Temp2 = SONG[Addr++];
TR0 = 1;
while(1)
{
_Speak = ~_Speak;
Delay_xMs(Temp1);
if ( Temp2 == Count )
{
Count = 0;
break;
}
}
}
}
}
/*-------------------------------------------------
功能:主程序
-------------------------------------------------*/
void main()
{
Time0_Init(); //定時器0中斷初始化
while(1)
{
Play_Song(0); //播放
}
}

復制代碼

其他的可以使用音樂代碼轉換器轉換即可，不過很麻煩而已！！！

ID:92909 · 發表于 2015-10-19 13:34

你好，請問你有音樂代碼轉換器嗎

ID:93224 · 發表于 2015-10-22 18:52

求電路圖

ID:93224 · 發表于 2015-10-22 18:53

求仿真圖

ID:107927 · 發表于 2016-3-9 16:15

這三個怎么組到一起啊，通過按鍵控制播放哪首歌曲。

ID:147796 · 發表于 2016-11-15 12:47

這三個怎么組到一起啊，通過按鍵控制播放哪首歌曲

ID:137916 · 發表于 2017-1-25 11:10

很好用厲害

ID:158729 · 發表于 2017-1-26 19:00

感謝分享，雖然譜出來不太好聽

ID:163075 · 發表于 2017-1-29 13:24

很有用啊

ID:202137 · 發表于 2017-5-18 13:02

各位大神！求解釋

ID:192926 · 發表于 2017-5-18 15:28

感謝分享。

ID:239541 · 發表于 2017-10-18 20:08

最近想弄弄這個謝謝分享

ID:241954 · 發表于 2017-10-22 22:24

超人強 發表于 2016-3-9 16:15
**** 作者被禁止或刪除內容自動屏蔽 ****

# include <stdio.h> //stdio.h 輸入輸出 printf scanf（輸入）在判斷選擇播放的歌

ID:241829 · 發表于 2017-10-28 19:48

請問為什么我添加到其他函數上

ID:238749 · 發表于 2017-11-26 18:19

樓主能問下如何在播放音樂的同時在主函數里做其他的事情嗎，我在主函數的play之后寫的其他程序與蜂鳴器沖突。

ID:272245 · 發表于 2018-1-16 14:44

我下載到單片機上不能用，蜂鳴器的端口改過了，這是怎么回事呢

ID:283896 · 發表于 2018-2-13 20:07

求轉換器

ID:338282 · 發表于 2018-5-25 18:42

lele5211314 發表于 2015-10-22 18:53
求仿真圖

加上最小系統，把小喇叭接到p^5扣

ID:351351 · 發表于 2018-7-15 17:36

stc12c5a60s2芯片可以能正常發音嗎？

ID:382249 · 發表于 2018-8-16 18:28

可以正常發聲，但是部分代碼不明白，求教里面*20 和 /3 什么意思？
void PlayMusic()
{
uint i=0,j,k;
while(SONG_LONG[i]!=0||SONG_TONE[i]!=0)
{ //播放各個音符，SONG_LONG 為拍子長度
for(j=0;j<SONG_LONG[i]*20;j++)
{
beep=~beep;
//SONG_TONE 延時表決定了每個音符的頻率
for(k=0;k<SONG_TONE[i]/3;k++);
}
DelayMS(10);
i++;
}
}

ID:385303 · 發表于 2018-8-16 21:34

可以，能不能把電路圖分享出來啊

ID:395167 · 發表于 2018-10-25 15:27

感謝分享

ID:358405 · 發表于 2020-5-27 12:24

感謝分享

帳號		自動登錄	找回密碼
密碼			立即注冊

wwwxxx国产_337p日本欧洲亚洲大胆张筱雨_免费在线看成人av_日本黄色不卡视频_国产精品成熟老女人_99视频一区_亚洲精品97久久中文字幕_免费精品视频在线_亚洲色图欧美视频_欧美一区二三区

51單片機蜂鳴器播放音樂代碼(生日快樂 兩只蝴蝶祝你平安)

評分

wwwxxx国产_337p日本欧洲亚洲大胆张筱雨_免费在线看成人av_日本黄色不卡视频_国产精品成熟老女人_99视频一区_亚洲精品97久久中文字幕_免费精品视频在线_亚洲色图欧美视频_欧美一区二三区

51單片機蜂鳴器播放音樂代碼(生日快樂 兩只蝴蝶 祝你平安)

評分

51單片機蜂鳴器播放音樂代碼(生日快樂 兩只蝴蝶祝你平安)